Skip to content
As·Ni

Arsenic and nickel

AAS / ICP on the filter digestResult in ng/m³EPA IO-3.4

Metal in the filter digest

Formulas, in order
Volume of air sampled · m³
V =Q×t
Arsenic and nickel in PM10 · ng/m³
C =(Mₛ−M_b)×Vₛ×Fₐ×1000(V×Fₜ)

Your readings

7 of 7 filled

Example values shown.

m³/min
min
µg/ml
µg/ml
ml
cm²
cm²
Arsenic and nickel in PM10Calculated live as you type
4.793 ng/m³ng/m³
Worked out with the formula above.

Calculations you finish this week are counted here, on this device only.

How arsenic and nickel is calculated

Free arsenic and nickel calculator (AAS / ICP on the filter digest method), following EPA IO-3.4. Enter 7 readings to get arsenic and nickel in PM10 in ng/m³, with the formula filled in step by step.

  1. Volume of air sampled · m³

    V = Q × t

  2. Arsenic and nickel in PM10 · ng/m³

    C = (Mₛ − M_b) × Vₛ × Fₐ × 1000 / (V × Fₜ)

What you need

SymbolReadingUnitNotes
QSampling ratem³/minusually 0.5–2 m³/min
tSampling timeminusually 60–1440 min
MₛConcentration in the sample digestµg/mlusually 0–10 µg/ml
M_bConcentration in the blank digestµg/mlusually 0–1 µg/ml
VₛTotal volume of extractmlusually 5–100 ml
FₐTotal exposed area of the filtercm²usually 10–600 cm²
FₜArea of filter taken for digestioncm²usually 1–600 cm²

Worked example

Readings:

  • Sampling rate: Q = 1.1 m³/min
  • Sampling time: t = 1440 min
  • Concentration in the sample digest: Mₛ = 0.042 µg/ml
  • Concentration in the blank digest: M_b = 0.004 µg/ml
  • Total volume of extract: Vₛ = 25 ml
  • Total exposed area of the filter: Fₐ = 406 cm²
  • Area of filter taken for digestion: Fₜ = 50.8 cm²
  1. Volume of air sampled

    V = 1.1 × 1440 = 1,584.0 m³

  2. Arsenic and nickel in PM10

    C = (0.042 − 0.004) × 25 × 406 × 1000 / (1,584.0 × 50.8) = 4.793 ng/m³

Result: Arsenic and nickel in PM10 4.793 ng/m³.

Checks and units

  • The sample digest reads lower than the blank.

Questions

How do you calculate arsenic and nickel by the AAS / ICP on the filter digest method?

Work through 2 steps in order. Volume of air sampled: V = Q × t. Arsenic and nickel in PM10: C = (Mₛ − M_b) × Vₛ × Fₐ × 1000 / (V × Fₜ). Here Q is the sampling rate (m³/min), t is the sampling time (min), Mₛ is the concentration in the sample digest (µg/ml), M_b is the concentration in the blank digest (µg/ml), Vₛ is the total volume of extract (ml), Fₐ is the total exposed area of the filter (cm²), Fₜ is the area of filter taken for digestion (cm²). The result is in ng/m³.

What unit is arsenic and nickel reported in?

Arsenic and nickel in PM10 is reported in ng/m³, to 3 decimal places.

Which standard does this arsenic and nickel calculation follow?

It follows the calculation in EPA IO-3.4. Check it against the current edition of the standard and your lab’s SOP before reporting.

Can you show a worked example?

With sampling rate = 1.1 m³/min, sampling time = 1440 min, concentration in the sample digest = 0.042 µg/ml, concentration in the blank digest = 0.004 µg/ml, total volume of extract = 25 ml, total exposed area of the filter = 406 cm², area of filter taken for digestion = 50.8 cm², the result is arsenic and nickel in PM10 = 4.793 ng/m³.

What mistakes should I look out for?

The sample digest reads lower than the blank.

Is this arsenic and nickel calculator free?

Yes. It’s free with no sign-up. The calculation runs in your browser and nothing you type is sent to NovaLIMS.

Related calculators

All ambient air calculators →

Check results against your own method and SOP before reporting. Found an error? Tell us and we’ll check it.

Run every calculation inside your LIMS

NovaLIMS puts these calculators right beside each sample’s parameters, for every analyst in the lab.