Skip to content
Pb

Lead

AAS / ICP on the filter digestResult in µg/m³IS 5182 (Part 22)

Metal in the filter digest

Formulas, in order
Volume of air sampled · m³
V =Q×t
Lead in PM10 · µg/m³
C =(Mₛ−M_b)×Vₛ×Fₐ(V×Fₜ)

Your readings

7 of 7 filled

Example values shown.

m³/min
min
µg/ml
µg/ml
ml
cm²
cm²
Lead in PM10Calculated live as you type
0.005 µg/m³µg/m³
Worked out with the formula above.

Calculations you finish this week are counted here, on this device only.

How lead is calculated

Free lead calculator (AAS / ICP on the filter digest method), following IS 5182 (Part 22). Enter 7 readings to get lead in PM10 in µg/m³, with the formula filled in step by step.

  1. Volume of air sampled · m³

    V = Q × t

  2. Lead in PM10 · µg/m³

    C = (Mₛ − M_b) × Vₛ × Fₐ / (V × Fₜ)

What you need

SymbolReadingUnitNotes
QSampling ratem³/minusually 0.5–2 m³/min
tSampling timeminusually 60–1440 min
MₛConcentration in the sample digestµg/mlusually 0–10 µg/ml
M_bConcentration in the blank digestµg/mlusually 0–1 µg/ml
VₛTotal volume of extractmlusually 5–100 ml
FₐTotal exposed area of the filtercm²usually 10–600 cm²
FₜArea of filter taken for digestioncm²usually 1–600 cm²

Worked example

Readings:

  • Sampling rate: Q = 1.1 m³/min
  • Sampling time: t = 1440 min
  • Concentration in the sample digest: Mₛ = 0.042 µg/ml
  • Concentration in the blank digest: M_b = 0.004 µg/ml
  • Total volume of extract: Vₛ = 25 ml
  • Total exposed area of the filter: Fₐ = 406 cm²
  • Area of filter taken for digestion: Fₜ = 50.8 cm²
  1. Volume of air sampled

    V = 1.1 × 1440 = 1,584.0 m³

  2. Lead in PM10

    C = (0.042 − 0.004) × 25 × 406 / (1,584.0 × 50.8) = 0.005 µg/m³

Result: Lead in PM10 0.005 µg/m³.

Checks and units

  • The sample digest reads lower than the blank.

Questions

How do you calculate lead by the AAS / ICP on the filter digest method?

Work through 2 steps in order. Volume of air sampled: V = Q × t. Lead in PM10: C = (Mₛ − M_b) × Vₛ × Fₐ / (V × Fₜ). Here Q is the sampling rate (m³/min), t is the sampling time (min), Mₛ is the concentration in the sample digest (µg/ml), M_b is the concentration in the blank digest (µg/ml), Vₛ is the total volume of extract (ml), Fₐ is the total exposed area of the filter (cm²), Fₜ is the area of filter taken for digestion (cm²). The result is in µg/m³.

What unit is lead reported in?

Lead in PM10 is reported in µg/m³, to 3 decimal places.

Which standard does this lead calculation follow?

It follows the calculation in IS 5182 (Part 22). Check it against the current edition of the standard and your lab’s SOP before reporting.

Can you show a worked example?

With sampling rate = 1.1 m³/min, sampling time = 1440 min, concentration in the sample digest = 0.042 µg/ml, concentration in the blank digest = 0.004 µg/ml, total volume of extract = 25 ml, total exposed area of the filter = 406 cm², area of filter taken for digestion = 50.8 cm², the result is lead in PM10 = 0.005 µg/m³.

What mistakes should I look out for?

The sample digest reads lower than the blank.

Is this lead calculator free?

Yes. It’s free with no sign-up. The calculation runs in your browser and nothing you type is sent to NovaLIMS.

Related calculators

All ambient air calculators →

Check results against your own method and SOP before reporting. Found an error? Tell us and we’ll check it.

Run every calculation inside your LIMS

NovaLIMS puts these calculators right beside each sample’s parameters, for every analyst in the lab.