Skip to content
510 nmFe

Iron

1,10-PhenanthrolineResult in mg/LIS 3025 (Part 53)

Turns orange-red · read at 510 nm

Formula
Fe =(A−B)×G.F×D

Your readings

5 of 5 filled

Example values shown.

ml
Abs
Abs
mg/L per Abs
Iron as FeCalculated live as you type
0.224 mg/L
Within the usual range. Drinking water: acceptable up to 1.0 mg/L.

Calculations you finish this week are counted here, on this device only.

How iron is calculated

Free iron calculator (1,10-Phenanthroline method), following IS 3025 (Part 53). Enter 5 readings to get iron as Fe in mg/L, with the formula filled in step by step.

  1. Iron as Fe · mg/L

    Fe = (A − B) × G.F × D

What you need

SymbolReadingUnitNotes
VVolume of sample takenmlusually 1–1000 ml
BAbsorbance of blankAbsusually 0–0.2 Abs
AAbsorbance of sampleAbsusually 0–2 Abs (the usual 0–2 absorbance range)
G.FGraph factormg/L per Absusually 0.01–500 mg/L per Abs
DDilution factor—usually 1–1000

Worked example

Readings:

  • Volume of sample taken: V = 50 ml
  • Absorbance of blank: B = 0.003 Abs
  • Absorbance of sample: A = 0.118 Abs
  • Graph factor: G.F = 1.95 mg/L per Abs
  • Dilution factor: D = 1
  1. Iron as Fe

    Fe = (0.118 − 0.003) × 1.95 × 1 = 0.224 mg/L

Result: Iron as Fe 0.224 mg/L.

Checks and units

  • Typical values: Drinking water: acceptable up to 1.0 mg/L
  • The sample reading (A) is lower than the blank (B), so the result would be negative. Check both.
  • Other units: ppm (1 mg/L ≈ 1 ppm in dilute water).

Questions

How do you calculate iron by the 1,10-Phenanthroline method?

Iron as Fe = (A − B) × G.F × D. Here V is the volume of sample taken (ml), B is the absorbance of blank (Abs), A is the absorbance of sample (Abs), G.F is the graph factor (mg/L per Abs), D is the dilution factor. The result is in mg/L.

What unit is iron reported in?

Iron as Fe is reported in mg/L, to 3 decimal places. The calculator can also show it in ppm (1 mg/L ≈ 1 ppm in dilute water).

Which standard does this iron calculation follow?

It follows the calculation in IS 3025 (Part 53). Check it against the current edition of the standard and your lab’s SOP before reporting.

Can you show a worked example?

With volume of sample taken = 50 ml, absorbance of blank = 0.003 Abs, absorbance of sample = 0.118 Abs, graph factor = 1.95 mg/L per Abs, dilution factor = 1, the result is iron as Fe = 0.224 mg/L.

What is a typical iron value?

Drinking water: acceptable up to 1.0 mg/L

What mistakes should I look out for?

The sample reading (A) is lower than the blank (B), so the result would be negative. Check both.

Is this iron calculator free?

Yes. It’s free with no sign-up. The calculation runs in your browser and nothing you type is sent to NovaLIMS.

Related calculators

All water & waste water calculators →

Check results against your own method and SOP before reporting. Found an error? Tell us and we’ll check it.

Run every calculation inside your LIMS

NovaLIMS puts these calculators right beside each sample’s parameters, for every analyst in the lab.