Skip to content
650 nmMBAS

Anionic surfactants

Methylene blue active substances (MBAS)Result in mg/LIS 13428 (Annex K)

Blue chloroform layer · read at 650 nm

Formula
MBAS =(A₁−A₀)×F×D

Your readings

5 of 5 filled

Example values shown.

ml
Abs
Abs
mg/L per Abs
Anionic surfactants as MBASCalculated live as you type
0.164 mg/L
Worked out with the formula above.

Calculations you finish this week are counted here, on this device only.

How anionic surfactants is calculated

Free anionic surfactants calculator (methylene blue active substances (MBAS) method), following IS 13428 (Annex K). Enter 5 readings to get anionic surfactants as MBAS in mg/L, with the formula filled in step by step.

  1. Anionic surfactants as MBAS · mg/L

    MBAS = (A₁ − A₀) × F × D

What you need

SymbolReadingUnitNotes
VVolume of sample takenmlusually 1–1000 ml
A₀Absorbance of the blankAbsusually 0–0.2 Abs
A₁Absorbance of the sampleAbsusually 0–2 Abs (the usual 0–2 absorbance range)
FCalibration factormg/L per Absusually 0.01–50 mg/L per Abs
DDilution factor—usually 1–1000

Worked example

Readings:

  • Volume of sample taken: V = 100 ml
  • Absorbance of the blank: A₀ = 0.01 Abs
  • Absorbance of the sample: A₁ = 0.188 Abs
  • Calibration factor: F = 0.92 mg/L per Abs
  • Dilution factor: D = 1
  1. Anionic surfactants as MBAS

    MBAS = (0.188 − 0.01) × 0.92 × 1 = 0.164 mg/L

Result: Anionic surfactants as MBAS 0.164 mg/L.

Checks and units

  • The sample absorbance is lower than the blank, so the result would be negative.
  • Other units: ppm (1 mg/L ≈ 1 ppm in dilute water).

Questions

How do you calculate anionic surfactants by the methylene blue active substances (MBAS) method?

Anionic surfactants as MBAS = (A₁ − A₀) × F × D. Here V is the volume of sample taken (ml), A₀ is the absorbance of the blank (Abs), A₁ is the absorbance of the sample (Abs), F is the calibration factor (mg/L per Abs), D is the dilution factor. The result is in mg/L.

What unit is anionic surfactants reported in?

Anionic surfactants as MBAS is reported in mg/L, to 3 decimal places. The calculator can also show it in ppm (1 mg/L ≈ 1 ppm in dilute water).

Which standard does this anionic surfactants calculation follow?

It follows the calculation in IS 13428 (Annex K). Check it against the current edition of the standard and your lab’s SOP before reporting.

Can you show a worked example?

With volume of sample taken = 100 ml, absorbance of the blank = 0.01 Abs, absorbance of the sample = 0.188 Abs, calibration factor = 0.92 mg/L per Abs, dilution factor = 1, the result is anionic surfactants as MBAS = 0.164 mg/L.

What mistakes should I look out for?

The sample absorbance is lower than the blank, so the result would be negative.

Is this anionic surfactants calculator free?

Yes. It’s free with no sign-up. The calculation runs in your browser and nothing you type is sent to NovaLIMS.

Related calculators

All water & waste water calculators →

Check results against your own method and SOP before reporting. Found an error? Tell us and we’ll check it.

Run every calculation inside your LIMS

NovaLIMS puts these calculators right beside each sample’s parameters, for every analyst in the lab.