Skip to content
664 nmH₂S

Sulphide

Methylene blueResult in mg/LIS 3025 (Part 29)

Turns blue · read at 664 nm

Formula
H₂S =(A−B)×G.F×D

Your readings

5 of 5 filled

Example values shown.

ml
Abs
Abs
mg/L per Abs
Sulphide as H₂SCalculated live as you type
0.374 mg/L
Within the usual range. Most treated effluents: below 2 mg/L.

Calculations you finish this week are counted here, on this device only.

How sulphide is calculated

Free sulphide calculator (methylene blue method), following IS 3025 (Part 29). Enter 5 readings to get sulphide as H₂S in mg/L, with the formula filled in step by step.

  1. Sulphide as H₂S · mg/L

    H₂S = (A − B) × G.F × D

What you need

SymbolReadingUnitNotes
VVolume of sample takenmlusually 1–1000 ml
BAbsorbance of blankAbsusually 0–0.2 Abs
AAbsorbance of sampleAbsusually 0–2 Abs (the usual 0–2 absorbance range)
G.FGraph factormg/L per Absusually 0.01–500 mg/L per Abs
DDilution factor—usually 1–1000

Worked example

Readings:

  • Volume of sample taken: V = 50 ml
  • Absorbance of blank: B = 0.012 Abs
  • Absorbance of sample: A = 0.214 Abs
  • Graph factor: G.F = 1.85 mg/L per Abs
  • Dilution factor: D = 1
  1. Sulphide as H₂S

    H₂S = (0.214 − 0.012) × 1.85 × 1 = 0.374 mg/L

Result: Sulphide as H₂S 0.374 mg/L.

Checks and units

  • Typical values: Most treated effluents: below 2 mg/L
  • The sample reading (A) is lower than the blank (B), so the result would be negative. Check both.
  • Other units: ppm (1 mg/L ≈ 1 ppm in dilute water).

Questions

How do you calculate sulphide by the methylene blue method?

Sulphide as H₂S = (A − B) × G.F × D. Here V is the volume of sample taken (ml), B is the absorbance of blank (Abs), A is the absorbance of sample (Abs), G.F is the graph factor (mg/L per Abs), D is the dilution factor. The result is in mg/L.

What unit is sulphide reported in?

Sulphide as H₂S is reported in mg/L, to 3 decimal places. The calculator can also show it in ppm (1 mg/L ≈ 1 ppm in dilute water).

Which standard does this sulphide calculation follow?

It follows the calculation in IS 3025 (Part 29). Check it against the current edition of the standard and your lab’s SOP before reporting.

Can you show a worked example?

With volume of sample taken = 50 ml, absorbance of blank = 0.012 Abs, absorbance of sample = 0.214 Abs, graph factor = 1.85 mg/L per Abs, dilution factor = 1, the result is sulphide as H₂S = 0.374 mg/L.

What is a typical sulphide value?

Most treated effluents: below 2 mg/L

What mistakes should I look out for?

The sample reading (A) is lower than the blank (B), so the result would be negative. Check both.

Is this sulphide calculator free?

Yes. It’s free with no sign-up. The calculation runs in your browser and nothing you type is sent to NovaLIMS.

Related calculators

All water & waste water calculators →

Check results against your own method and SOP before reporting. Found an error? Tell us and we’ll check it.

Run every calculation inside your LIMS

NovaLIMS puts these calculators right beside each sample’s parameters, for every analyst in the lab.