Skip to content
640 nmNH₃

Ammonia

ColorimetricResult in µg/m³IS 5182 (Part 25)

Read at 640 nm

Formulas, in order
Volume of air sampled · m³
Va =Q×t1000
Ammonia · µg/m³
NH₃ =(Aₛ−A_b)×CFVa

Your readings

5 of 5 filled

Example values shown.

µg per Abs
L/min
min
Abs
Abs
AmmoniaCalculated live as you type
9.3 µg/m³µg/m³
Within the usual range. 24-hour standard (NAAQS): 400 µg/m³.

Calculations you finish this week are counted here, on this device only.

How ammonia is calculated

Free ammonia calculator (colorimetric method), following IS 5182 (Part 25). Enter 5 readings to get ammonia in µg/m³, with the formula filled in step by step.

  1. Volume of air sampled · m³

    Va = Q × t / 1000

  2. Ammonia · µg/m³

    NH₃ = (Aₛ − A_b) × CF / Va

What you need

SymbolReadingUnitNotes
CFCalibration factorµg per Absusually 0.1–200 µg per Abs
QAverage flow rateL/minusually 0.1–5 L/min
tSampling timeminusually 10–1440 min
AₛAbsorbance of sampleAbsusually 0–2 Abs
A_bAbsorbance of blankAbsusually 0–0.2 Abs

Worked example

Readings:

  • Calibration factor: CF = 42 µg per Abs
  • Average flow rate: Q = 1 L/min
  • Sampling time: t = 480 min
  • Absorbance of sample: Aₛ = 0.118 Abs
  • Absorbance of blank: A_b = 0.012 Abs
  1. Volume of air sampled

    Va = 1 × 480 / 1000 = 0.4800 m³

  2. Ammonia

    NH₃ = (0.118 − 0.012) × 42 / 0.4800 = 9.3 µg/m³

Result: Ammonia 9.3 µg/m³.

Checks and units

  • Typical values: 24-hour standard (NAAQS): 400 µg/m³
  • The sample absorbance is lower than the blank, so the result would be negative.

Questions

How do you calculate ammonia by the colorimetric method?

Work through 2 steps in order. Volume of air sampled: Va = Q × t / 1000. Ammonia: NH₃ = (Aₛ − A_b) × CF / Va. Here CF is the calibration factor (µg per Abs), Q is the average flow rate (L/min), t is the sampling time (min), Aₛ is the absorbance of sample (Abs), A_b is the absorbance of blank (Abs). The result is in µg/m³.

What unit is ammonia reported in?

Ammonia is reported in µg/m³, to 1 decimal place.

Which standard does this ammonia calculation follow?

It follows the calculation in IS 5182 (Part 25). Check it against the current edition of the standard and your lab’s SOP before reporting.

Can you show a worked example?

With calibration factor = 42 µg per Abs, average flow rate = 1 L/min, sampling time = 480 min, absorbance of sample = 0.118 Abs, absorbance of blank = 0.012 Abs, the result is ammonia = 9.3 µg/m³.

What is a typical ammonia value?

24-hour standard (NAAQS): 400 µg/m³

What mistakes should I look out for?

The sample absorbance is lower than the blank, so the result would be negative.

Is this ammonia calculator free?

Yes. It’s free with no sign-up. The calculation runs in your browser and nothing you type is sent to NovaLIMS.

Related calculators

All ambient air calculators →

Check results against your own method and SOP before reporting. Found an error? Tell us and we’ll check it.

Run every calculation inside your LIMS

NovaLIMS puts these calculators right beside each sample’s parameters, for every analyst in the lab.