Skip to content
Cl⁻

Chloride

ArgentometricResult in mg/LIS 3025 (Part 32)

Yellow → brick-red at the endpoint (chromate indicator)

Formula
Cl⁻ =(A−B)×N×35.45×1000×DV

Your readings

5 of 5 filled

Example values shown.

ml
N
ml
ml
Atomic weight of chlorineConstant · fixed by the method35.45🔒
Chloride as Cl⁻Calculated live as you type
48.98 mg/L
Within the usual range. Most drinking and ground water: up to 1,000 mg/L.

Calculations you finish this week are counted here, on this device only.

How chloride is calculated

Free chloride calculator (argentometric method), following IS 3025 (Part 32). Enter 5 readings to get chloride as Cl⁻ in mg/L, with the formula filled in step by step.

  1. Chloride as Cl⁻ · mg/L

    Cl⁻ = (A − B) × N × 35.45 × 1000 × D / V

What you need

SymbolReadingUnitNotes
VVolume of sample takenmlusually 1–1000 ml
NNormality of AgNO₃Nusually 0.005–0.1 N
BAgNO₃ used for blankmlusually 0–2 ml
AAgNO₃ used for samplemlusually 0–50 ml (a 50 ml burette)
DDilution factor—usually 1–1000

Fixed values in the formula

SymbolConstantValue
35.45Atomic weight of chlorine35.45

Worked example

Readings:

  • Volume of sample taken: V = 50 ml
  • Normality of AgNO₃: N = 0.0141 N
  • AgNO₃ used for blank: B = 0.2 ml
  • AgNO₃ used for sample: A = 5.1 ml
  • Dilution factor: D = 1
  1. Chloride as Cl⁻

    Cl⁻ = (5.1 − 0.2) × 0.0141 × 35.45 × 1000 × 1 / 50 = 48.98 mg/L

Result: Chloride as Cl⁻ 48.98 mg/L.

Checks and units

  • Typical values: Most drinking and ground water: up to 1,000 mg/L
  • The sample titre (A) is less than the blank (B), so the result would be negative. Check both readings.
  • Other units: ppm (1 mg/L ≈ 1 ppm in dilute water); meq/L (Equivalent weight of Cl⁻: 35.45).

Questions

How do you calculate chloride by the argentometric method?

Chloride as Cl⁻ = (A − B) × N × 35.45 × 1000 × D / V. Here V is the volume of sample taken (ml), N is the normality of AgNO₃ (N), B is the AgNO₃ used for blank (ml), A is the AgNO₃ used for sample (ml), D is the dilution factor. The result is in mg/L.

What unit is chloride reported in?

Chloride as Cl⁻ is reported in mg/L, to 2 decimal places. The calculator can also show it in ppm (1 mg/L ≈ 1 ppm in dilute water), meq/L (Equivalent weight of Cl⁻: 35.45).

Which standard does this chloride calculation follow?

It follows the calculation in IS 3025 (Part 32). Check it against the current edition of the standard and your lab’s SOP before reporting.

Can you show a worked example?

With volume of sample taken = 50 ml, normality of AgNO₃ = 0.0141 N, AgNO₃ used for blank = 0.2 ml, AgNO₃ used for sample = 5.1 ml, dilution factor = 1, the result is chloride as Cl⁻ = 48.98 mg/L.

What is a typical chloride value?

Most drinking and ground water: up to 1,000 mg/L

What mistakes should I look out for?

The sample titre (A) is less than the blank (B), so the result would be negative. Check both readings.

Is this chloride calculator free?

Yes. It’s free with no sign-up. The calculation runs in your browser and nothing you type is sent to NovaLIMS.

Related calculators

All water & waste water calculators →

Check results against your own method and SOP before reporting. Found an error? Tell us and we’ll check it.

Run every calculation inside your LIMS

NovaLIMS puts these calculators right beside each sample’s parameters, for every analyst in the lab.