Skip to content
420 nmSO₄²⁻

Sulphate

TurbidimetricResult in mg/LIS 3025 (Part 24)

Turns milky white · read at 420 nm

Formula
SO₄²⁻ =(A−B)×G.F×D

Your readings

5 of 5 filled

Example values shown.

ml
Abs
Abs
mg/L per Abs
Sulphate as SO₄²⁻Calculated live as you type
31.77 mg/L
Worked out with the formula above.

Calculations you finish this week are counted here, on this device only.

How sulphate is calculated

Free sulphate calculator (turbidimetric method), following IS 3025 (Part 24). Enter 5 readings to get sulphate as SO₄²⁻ in mg/L, with the formula filled in step by step.

  1. Sulphate as SO₄²⁻ · mg/L

    SO₄²⁻ = (A − B) × G.F × D

What you need

SymbolReadingUnitNotes
VVolume of sample takenmlusually 1–1000 ml
BAbsorbance of blankAbsusually 0–0.2 Abs
AAbsorbance of sampleAbsusually 0–2 Abs (the usual 0–2 absorbance range)
G.FGraph factormg/L per Absusually 0.5–500 mg/L per Abs
DDilution factor—usually 1–1000

Worked example

Readings:

  • Volume of sample taken: V = 100 ml
  • Absorbance of blank: B = 0.008 Abs
  • Absorbance of sample: A = 0.312 Abs
  • Graph factor: G.F = 104.5 mg/L per Abs
  • Dilution factor: D = 1
  1. Sulphate as SO₄²⁻

    SO₄²⁻ = (0.312 − 0.008) × 104.5 × 1 = 31.77 mg/L

Result: Sulphate as SO₄²⁻ 31.77 mg/L.

Checks and units

  • The sample reading (A) is lower than the blank (B), so the result would be negative. Check both.
  • Other units: ppm (1 mg/L ≈ 1 ppm in dilute water); meq/L (Equivalent weight of SO₄²⁻: 48.03).

Questions

How do you calculate sulphate by the turbidimetric method?

Sulphate as SO₄²⁻ = (A − B) × G.F × D. Here V is the volume of sample taken (ml), B is the absorbance of blank (Abs), A is the absorbance of sample (Abs), G.F is the graph factor (mg/L per Abs), D is the dilution factor. The result is in mg/L.

What unit is sulphate reported in?

Sulphate as SO₄²⁻ is reported in mg/L, to 2 decimal places. The calculator can also show it in ppm (1 mg/L ≈ 1 ppm in dilute water), meq/L (Equivalent weight of SO₄²⁻: 48.03).

Which standard does this sulphate calculation follow?

It follows the calculation in IS 3025 (Part 24). Check it against the current edition of the standard and your lab’s SOP before reporting.

Can you show a worked example?

With volume of sample taken = 100 ml, absorbance of blank = 0.008 Abs, absorbance of sample = 0.312 Abs, graph factor = 104.5 mg/L per Abs, dilution factor = 1, the result is sulphate as SO₄²⁻ = 31.77 mg/L.

What mistakes should I look out for?

The sample reading (A) is lower than the blank (B), so the result would be negative. Check both.

Is this sulphate calculator free?

Yes. It’s free with no sign-up. The calculation runs in your browser and nothing you type is sent to NovaLIMS.

Related calculators

All water & waste water calculators →

Check results against your own method and SOP before reporting. Found an error? Tell us and we’ll check it.

Run every calculation inside your LIMS

NovaLIMS puts these calculators right beside each sample’s parameters, for every analyst in the lab.