Skip to content
570 nmF⁻

Fluoride

SPADNSResult in mg/LIS 3025 (Part 60)

Red reagent fades · read at 570 nm

Fluoride bleaches the red SPADNS reagent: the more fluoride, the lower the absorbance.

Formula
F⁻ =(A₀−Aₓ)(A₀−A₁)×D

Your readings

5 of 5 filled

Example values shown.

ml
Abs
Abs
Abs
Fluoride as F⁻Calculated live as you type
0.55 mg/L
Within the usual range. Drinking water: acceptable up to 1.0 mg/L.

Calculations you finish this week are counted here, on this device only.

How fluoride is calculated

Free fluoride calculator (SPADNS method), following IS 3025 (Part 60). Enter 5 readings to get fluoride as F⁻ in mg/L, with the formula filled in step by step.

  1. Fluoride as F⁻ · mg/L

    F⁻ = (A₀ − Aₓ) / (A₀ − A₁) × D

What you need

SymbolReadingUnitNotes
VVolume of sample takenmlusually 1–1000 ml
A₀Absorbance of the blankAbsusually 0–2 Abs (the usual 0–2 absorbance range)
AₓAbsorbance of the sampleAbsusually 0–2 Abs (the usual 0–2 absorbance range)
A₁Absorbance of a 1 mg/L fluoride standardAbsusually 0–2 Abs (the usual 0–2 absorbance range)
DDilution factor—usually 1–1000

Worked example

Readings:

  • Volume of sample taken: V = 50 ml
  • Absorbance of the blank: A₀ = 0.512 Abs
  • Absorbance of the sample: Aₓ = 0.398 Abs
  • Absorbance of a 1 mg/L fluoride standard: A₁ = 0.306 Abs
  • Dilution factor: D = 1
  1. Fluoride as F⁻

    F⁻ = (0.512 − 0.398) / (0.512 − 0.306) × 1 = 0.55 mg/L

Result: Fluoride as F⁻ 0.55 mg/L.

Checks and units

  • Typical values: Drinking water: acceptable up to 1.0 mg/L
  • The sample absorbance is above the blank; fluoride bleaches the colour, so check the readings.
  • The blank and the standard read the same: the standard can't be used.
  • Other units: ppm (1 mg/L ≈ 1 ppm in dilute water); meq/L (Equivalent weight of F⁻: 19).

Questions

How do you calculate fluoride by the SPADNS method?

Fluoride as F⁻ = (A₀ − Aₓ) / (A₀ − A₁) × D. Here V is the volume of sample taken (ml), A₀ is the absorbance of the blank (Abs), Aₓ is the absorbance of the sample (Abs), A₁ is the absorbance of a 1 mg/L fluoride standard (Abs), D is the dilution factor. The result is in mg/L.

What unit is fluoride reported in?

Fluoride as F⁻ is reported in mg/L, to 2 decimal places. The calculator can also show it in ppm (1 mg/L ≈ 1 ppm in dilute water), meq/L (Equivalent weight of F⁻: 19).

Which standard does this fluoride calculation follow?

It follows the calculation in IS 3025 (Part 60). Check it against the current edition of the standard and your lab’s SOP before reporting.

Can you show a worked example?

With volume of sample taken = 50 ml, absorbance of the blank = 0.512 Abs, absorbance of the sample = 0.398 Abs, absorbance of a 1 mg/L fluoride standard = 0.306 Abs, dilution factor = 1, the result is fluoride as F⁻ = 0.55 mg/L.

What is a typical fluoride value?

Drinking water: acceptable up to 1.0 mg/L

What mistakes should I look out for?

The sample absorbance is above the blank; fluoride bleaches the colour, so check the readings. The blank and the standard read the same: the standard can't be used.

Is this fluoride calculator free?

Yes. It’s free with no sign-up. The calculation runs in your browser and nothing you type is sent to NovaLIMS.

Related calculators

All water & waste water calculators →

Check results against your own method and SOP before reporting. Found an error? Tell us and we’ll check it.

Run every calculation inside your LIMS

NovaLIMS puts these calculators right beside each sample’s parameters, for every analyst in the lab.